FREE UK SHIPPING!   Tel: 01902 581 301  Mon-Fri  9am-5pm
Six String Supplies — Copper Shielding - How to Shield a Guitar

Copper Shielding - How to Shield a Guitar

In this guide (and the above video) we will show you how to create a “Faraday cage” protecting your guitar’s electronics from outside interference using copper shielding tape, the most popular way to shield your guitar. This guide covers how to shield a Strat but the principle is the same regardless of what model you use.

Kill The Buzz!

Electro-magnetic interference (EMI) is a common feature of electric guitars. Interference from other electrical devices such as amplifiers and lights can cause unwanted electronic feedback (especially when playing on a stage with lots of gear and stage lights). It is particularly common with single coil pickups (more so than humbuckers), which is why many guitarists shield their guitar.

The Science

The idea of shielding is to create a “Faraday cage” around the electronic components (basically a conductive enclosure) inside your guitar; pots, switches, wiring and pickups etc… The electronics inside your guitar act as antennae for nearby electrical equipment and so unshielded guitars are vulnerable to the inevitable feedback. This is caused by radio frequencies and electrostatic fields.

Creating a Faraday cage around the electronics and wiring helps to protect the guitar from external devices and reduces unwanted feedback by blocking incoming frequencies.

It’s not just shielding that helps to combat this feedback – insulated wire and superior quality components all help.

Conductive shielding paint or Copper Foil?

There are two main methods to shield a guitar – shielding graphite paint (conductive paint) or more commonly, aluminium or copper foil.

Many guitars will come from the factory with conductive paint covering the control and pickup cavities but this is not always the most effective way to shield a guitar. On top of this, conductive (graphite) paint is a lot more expensive – you only justify the price if you are shielding several guitars. It also takes several coats of the paint to reach a suitable level of continuity.

Copper or aluminium foil are more readily available and a cheaper alternative. At the end of the video, we’ll show you the difference between graphite paint and copper tape on the multimeter.

To shield your guitar you will need;

- 2-3m of 50mm wide copper shielding tape (with conductive adhesive)

- Scissors and box cutter (or similar suitable blade)

- A digital multimeter

NOTE - while this is hardly a dangerous job, the edges of the copper foil tape can become very sharp. Watch your fingers!

The Pickguard

We’ll start by shielding the pickguard. Most Strat pickguards will come from the factory with aluminium foil acting as a grounding plate surrounding the switch, tone and volume controls. This is sufficient for a grounding plate but offers little to no shielding and not even close to creating a Faraday cage.

Using your 50mm wide copper tape – lay strips across the pickguard, covering it length ways. Make sure each strip is in contact with the previous by overlapping each strip by 5mm or so. Keep laying down strips until you have covered the whole pickguard. Use your scissors to cut the tape to the desired length. Each strip of tape needs to be as flat as possible with no tears or gaps.

Once the whole pickguard is covered, use a box cutter or suitable blade to carefully trace through the pickup, controls and screw holes.

To test conductivity – use your multimeter on the continuity test setting….if you have done it properly, you should have full conductivity between any given two points on the pickguard.

The Body

Use the same principle when shielding the inside of the body – carefully lay cut to size strips which overlap each other. Your scissors will become useful to cut strips to desired lengths and smaller widths to fit copper into all the little nooks and cranny’s. Use cut strips of copper tape lengthways running up the sides and use the full width (50mm) to do the floor of the cavity.

Most importantly – make sure the tape runs up the sides and on to the top of the body as shown in the photo below. The idea being, when the pickguard is screwed back into place, the copper on the underside comes into contact with the copper within the body, thereby creating the Faraday cage.

Repeat this process until the whole cavity is covered. Pay attention to ensure each strip overlaps the previous one, as well as making sure the tape goes over the edge.

Again, once you have completed shielding the inside of the body, test for continuity using the multimeter.

The Faraday Cage

Having completed copper shielding the pickguard and body you now have the makings of a Faraday cage. To test this out, place the pickguard back on top of the body. Using the multimeter test for continuity between the pickguard and the body as we have done in the below photo. This means, that when you have screwed the pickguard back down you know that the copper underneath the pickguard is connected to the foil in the body - thereby creating the conductive enclosure required.

There you have it – how to shield a guitar. Unfortunately, RF (radio frequencies) and EMI (electro-magnetic interference) are inevitable with electronic equipment. It is impossible to completely shield your guitar from their waves (short of putting it inside a metal box) but you can go a long way to reducing the impact and unwanted electronic feedback while playing.

Share

How to wire a Switchcraft 3-way toggle switch

How to wire a Les Paul

How to wire a Stratocaster

How to Wire a Telecaster

How to Wire a Les Paul Junior

Treble Bleed Mod